Bush-hog 280 Manuale Utente

BUSH HOG®ASSEMBLY ● OPERATION ● MAINTENANCE$4.00Operator’s Manual280 SERIESROTARY CUTTERS 199Part No. 95355

9Figure 2-3H. Hold driveline sections parallel to each otherand check for minimum 6 inches (15cm) overlap.Figure 2-4). If driveline has been marked fo

SECTION IIIOPERATING INSTRUCTIONS3-1 GENERAL SAFETYOnly qualified people should operate this machine.Operator should wear hard hat, safety glasses and

ROTATING CUTTER BLADES. STAND CLEAR UNTIL ALL MOTION HAS STOPPED. TO AVOID AN ACCIDENTAL FALL FROM THE TRACTOR AND POSSIBLE INJURY BY THE MOWER, IT

12Figure 4-1 Lubrication(3) Before Each Use(2) Before Each Use(6) Before Each Use4-4 BLADE REPLACEMENT (Figure 4-2)It is not necessary to remove the c

(SeeChart)Figure 4-3Spring LengthMODEL SPRING LENGTH285 &286 1-3/32” or 27.6 mm287

PRE-ASSEMBLYSAFETY PRECAUTIONSTHE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY.1. Wear personal pro

SECTION VASSEMBLYIMPORTANTTighten all fasteners to specifications on TorqueChart unless otherwise indicated.5-1 3-POINT LIFT MODELS (285 & 286)A.

5-2 3-POINT LIFT MODELS (287)A. Attach A-frame struts to mounting bracketsusing 5/8” x 2” capscrews and locknuts as shown.(Fig. 5-1)B. Place flex li

5-3 SEMI-MOUNT MODEL (287)A. For mounting dual tailwheels, position tailwheelbrackets at the rear tubes located in the strong-backs. (Figure 5-2) Al

185-5 FRONT BELTING INSTALLATIONA. Align belting and clamp with holes in front lipof deck.B. Fasten with 3/8 x 3-1/2” capscrews, flatwash-ers, lockwas

CONGRATULATIONS!You have invested in the best implement of its type on the market today.The care you give your Bush Hog implement will greatly determi

SAFETY DECALSTo promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagecan occur to safety decals either

TORQUE SPECIFICATIONSProper toque for American fasteners used on Bush Hog equipment.Recommended Torque in Foot Pounds (Newton Meters).*BOLT DIAMETERWR

MODEL 287 QUICK HITCH ASSEMBLYNOTEPivot arm must be assembled as shown so that it willpivot upward as the hitch assembly flexes. Pointedend must be to

DIVISION OFP.O. Box 1039 ● Selma, AL 36702-1039Telephone (334) 872-6261BUSH HOG

280 SERIES ROTARY CUTTERSTABLE OF CONTENTSSECTION/PARA PAGEWarranty...3D

BUSH HOG®MODEL 280 SERIES LIMITED WARRANTY✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯Bush Hog warrants to the original purchaser of any new Bush Hog equipment, pu

DEALER PREPARATION CHECK LIST280 SERIES ROTARY CUTTERSBEFORE DELIVERING MACHINE — The following check list should be completed.Use the Operator’s Manu

IMPORTANT SAFETY PRECAUTIONSThis symbol is used to call attention to safe-ty precautions that should be followed by the operator to avoid accidents. W

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNINGEMPLOYERS, EMPLOYEES AND OPERATIONS.*(This section is intended to explain in broad terms the concept

1-1 INTRODUCTIONWe are pleased to have you as a Bush Hog cus-tomer. Your 280 Series Rotary Cutter has beencarefully designed to give maximum service

Figure 2-1 Top Link Pin5-1/2”3-3/4”3-3/4”8NOTEDue to the many variations in tractor / imple-ment hitch points and corresponding differ-ences in distan